SavsMom
New member
Checked this out at BRU - its a really cool seat. Wish they would have made the top slots at least 18", but oh well, and there is a problem with the harness adjuster - see the last pic for that problem and please chime in on it.
My favorite part - install. This seat has rigid latch and it is great great great. You just hit the release levers, the rigid latch connectors pop out, you slide the seat onto the latch in your car, push the yellow tabs and push the seat back into place - rock solid install in less than 2 minutes my first try. I installed the seat in my 2010 Toyota Prius.
DD just turned 4 in December. She is currently 31 lbs, 39" tall with a torso that is about 15.5" - she is very leggy.
She would be on the 6th harness slot (there are 8 total), with about 2" of harness height to go.
Bottom harness height is about 12" - I could have pushed down on the seat pad to show it a bit more accurate, but you get the idea.
Top harness height is 17" - again, could have pushed down on the seat pad to show it a bit more accurate - its hard to hold a tape measure, push down to get accurate length AND hold a camera and take a pic.
Internal seating width is about 11" going out to about 12" between the cupholder and media holder.
Top Harness Position from the side
The harness could be a problem, I am not sure, I put the harness down lower and was trying to tighten it and couldn't. I uninstalled the seat and found that the harness splitter plate stops the harness from getting any tighter - because of the way it is routed? Any insight on this?
There are 2 positions for the crotch buckle that measured at 5" and 6" - and the crotch buckle is a decent length.
Internal seating depth is about 12". DD also has a Maestro and this seat gives her a bit more leg support than the Maestro.
Overall its a pretty cool seat, just wish the harness wasn't routed so strange and if they could have gotten to at least 18" harness height it would be even better.
My favorite part - install. This seat has rigid latch and it is great great great. You just hit the release levers, the rigid latch connectors pop out, you slide the seat onto the latch in your car, push the yellow tabs and push the seat back into place - rock solid install in less than 2 minutes my first try. I installed the seat in my 2010 Toyota Prius.
DD just turned 4 in December. She is currently 31 lbs, 39" tall with a torso that is about 15.5" - she is very leggy.
She would be on the 6th harness slot (there are 8 total), with about 2" of harness height to go.
Bottom harness height is about 12" - I could have pushed down on the seat pad to show it a bit more accurate, but you get the idea.
Top harness height is 17" - again, could have pushed down on the seat pad to show it a bit more accurate - its hard to hold a tape measure, push down to get accurate length AND hold a camera and take a pic.
Internal seating width is about 11" going out to about 12" between the cupholder and media holder.
Top Harness Position from the side
The harness could be a problem, I am not sure, I put the harness down lower and was trying to tighten it and couldn't. I uninstalled the seat and found that the harness splitter plate stops the harness from getting any tighter - because of the way it is routed? Any insight on this?
There are 2 positions for the crotch buckle that measured at 5" and 6" - and the crotch buckle is a decent length.
Internal seating depth is about 12". DD also has a Maestro and this seat gives her a bit more leg support than the Maestro.
Overall its a pretty cool seat, just wish the harness wasn't routed so strange and if they could have gotten to at least 18" harness height it would be even better.